상품명 | Devantech SRF05 - Low cost Ultrasonic Ranger 저가형 초음파 거리계 |
---|---|
원산지 | 영국 |
판매가 | 27,000원 |
세액 | 2,700원 |
수량 | |
관련상품수 | 0 |
배송 | |
---|---|
수량 |
상품 정보 | 가격 | 삭제 |
---|---|---|
총상품금액(수량) 0 |
상품명 | Devantech SRF05 - Low cost Ultrasonic Ranger 저가형 초음파 거리계 |
---|---|
원산지 | 영국 |
판매가 | 27,000원 |
세액 | 2,700원 |
수량 | |
관련상품수 | 0 |
5개 이상 주문 시 별도 메일 발주 하세요(할인 해 드립니다)
SRF05 - New! Low Cost Ultrasonic Range Finder
SRF05 - New! Low Cost Ultrasonic Range Finder
- SRF04와 100%호환 모드 지원합니다(2 Wire Mode).
- 새로운 1 Wire Mode 지원, 1 포트로 트리거 및 에코 동시에 수행. ==> 소중한 포트 절약!!
- 저가, 전전력이면서도 거리를 3m에서 4m로 늘였습니다.
Voltage - 5v only required
Current - 4mA Typ. 50mA Max.
Frequency - 40KHz
Max Range - 4 m
Min Range - 1 cm
Modes - Single pin for trig/echo or 2 Pin SRF04 compatible.
Input Trigger - 10uS Min. TTL level pulse
Echo Pulse - Positive TTL level signal, width proportional to range.
Small Size - 43mm x 20mm x 17mm height (SRF04와 동일 크기)
* 자세한 기술자료는 자료실에 있습니다.
SRF05 - Ultra-Sonic Ranger
Technical Specification
Introduction
The SRF05 is an evolutionary step from the SRF04, and has been designed to increase flexibility, increase range, and to reduce costs still further. As such, the SRF05 is fully compatible with the SRF04. Range is increased from 3 meters to 4 meters. A new operating mode (tying the mode pin to ground) allows the SRF05 to use a single pin for both trigger and echo, thereby saving valuable pins on your controller. When the mode pin is left unconnected, the SRF05 operates with separate trigger and echo pins, like the SRF04. The SRF05 includes a small delay before the echo pulse to give slower controllers such as the Basic Stamp and Picaxe time to execute their pulse in commands.
Mode 1 - SRF04 compatible - Separate Trigger and Echo
This mode uses separate trigger and echo pins, and is the simplest mode to use. All code examples for the SRF04 will work for the SRF05 in this mode. To use this mode, just leave the mode pin unconnected - the SRF05 has an internal pull up resistor on this pin.
Mode 2 - Single pin for both Trigger and Echo
This mode uses a single pin for both Trigger and Echo signals, and is designed to save valuable pins on embedded controllers. To use this mode, connect the mode pin to the 0v Ground pin. The echo signal will appear on the same pin as the trigger signal. The SRF05 will not raise the echo line until 700uS after the end of the trigger signal. You have that long to turn the trigger pin around and make it an input and to have your pulse measuring code ready. The PULSIN command found on many popular controllers does this automatically.
To use mode 2 with the Basic Stamp BS2, you simply use PULSOUT and PULSIN on the same pin, like this:
SRF05 PIN 15 ' use any pin for both trigger and echo Range VAR Word ' define the 16 bit range variable SRF05 = 0 ' start with pin low PULSOUT SRF05, 5 ' issue 10uS trigger pulse (5 x 2uS) PULSIN SRF05, 1, Range ' measure echo time Range = Range/29 ' convert to cm (divide by 74 for inches) |
Calculating the Distance
The SRF05 Timing diagrams are shown above for each mode. You only need to supply a short 10uS pulse to the trigger input to start the ranging. The SRF05 will send out an 8 cycle burst of ultrasound at 40khz and raise its echo line high (or trigger line in mode 2). It then listens for an echo, and as soon as it detects one it lowers the echo line again. The echo line is therefore a pulse whose width is proportional to the distance to the object. By timing the pulse it is possible to calculate the range in inches/centimeters or anything else. If nothing is detected then the SRF05 will lower its echo line anyway after about 30mS.
The SRF04 provides an echo pulse proportional to distance. If the width of the pulse is measured in uS, then dividing by 58 will give you the distance in cm, or dividing by 148 will give the distance in inches. uS/58=cm or uS/148=inches.
The SRF05 can be triggered as fast as every 50mS, or 20 times each second. You should wait 50ms before the next trigger, even if the SRF05 detects a close object and the echo pulse is shorter. This is to ensure the ultrasonic "beep" has faded away and will not cause a false echo on the next ranging.
The other set of 5 pins
The 5 pins marked "programming pins" are used once only during manufacture to program the Flash memory on the PIC16F630 chip. The PIC16F630's programming pins are also used for other functions on the SRF05, so make sure you don't connect anything to these pins, or you will disrupt the modules operation.
Changing beam pattern and beam width
You can't! This is a question which crops up regularly, however there is no easy way to reduce or change the beam width that I'm aware of. The beam pattern of the SRF05 is conical with the width of the beam being a function of the surface area of the transducers and is fixed. The beam pattern of the transducers used on the SRF05, taken from the manufacturers data sheet, is shown below.
교환 및 반품이 가능한 경우
- 상품을 공급 받으신 날로부터 7일이내 단, 가전제품의
경우 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우에는 교환/반품이 불가능합니다.
- 공급받으신 상품 및 용역의 내용이 표시.광고 내용과
다르거나 다르게 이행된 경우에는 공급받은 날로부터 3월이내, 그사실을 알게 된 날로부터 30일이내
교환 및 반품이 불가능한 경우
- 고객님의 책임 있는 사유로 상품등이 멸실 또는 훼손된 경우. 단, 상품의 내용을 확인하기 위하여
포장 등을 훼손한 경우는 제외
- 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우
(예 : 가전제품, 식품, 음반 등, 단 액정화면이 부착된 노트북, LCD모니터, 디지털 카메라 등의 불량화소에
따른 반품/교환은 제조사 기준에 따릅니다.)
- 고객님의 사용 또는 일부 소비에 의하여 상품의 가치가 현저히 감소한 경우 단, 화장품등의 경우 시용제품을
제공한 경우에 한 합니다.
- 시간의 경과에 의하여 재판매가 곤란할 정도로 상품등의 가치가 현저히 감소한 경우
- 복제가 가능한 상품등의 포장을 훼손한 경우
(자세한 내용은 고객만족센터 1:1 E-MAIL상담을 이용해 주시기 바랍니다.)
※ 고객님의 마음이 바뀌어 교환, 반품을 하실 경우 상품반송 비용은 고객님께서 부담하셔야 합니다.
(색상 교환, 사이즈 교환 등 포함)
※ 상품구입후 단순변심은 환불되지 않습니다.
A/S 안내
- 전자키트 및 센서 에 대하여 조립시 A/S 및 환불이 되지 않습니다.
- 전자키트 초기 불량일 경우 100% A/S 조치해 드립니다.
- 완제품 의 경우 외산의 제품이 대부분이여서 한달간 무상수리해드립니다.(국산품 제외)
- 완제품 국산제품의 경우 제조사의 A/S 조항을 따릅니다.
051-465-7774
AM 9:00 ~ PM 18:00
LUNCH PM 12:00 ~ PM 13:00
CLOSED토요일, 일요일, 법정공휴일