Eltec Pyroelectric Detectors (Sensors)

뒤로가기

상품 상세 정보
상품명 Eltec Pyroelectric Detectors (Sensors)
원산지 Switzerland
판매가 메일 상담
수량 수량증가수량감소
관련상품수 0
배송
수량 up down  
상품 목록
상품 정보 가격 삭제
총상품금액(수량) 0
buy it now
BUY IT NOW
상품 상세 정보
상품명 Eltec Pyroelectric Detectors (Sensors)
원산지 Switzerland
판매가 메일 상담
수량 수량증가수량감소
관련상품수 0

서비스문의 안내

상품문의 및 서비스 문의는 아래 메일 또는 휴대폰으로 SNS 연락주시면 즉시 처리해 드리도록 하겠습니다. E-mail:easykit@daum.net /swplanet@naver.com Mobile: 010-6217-4800
상세페이지는 손가락을 이용하여 확대가 가능합니다



고도의 품질과 정밀성을 요구하는 사용자님을 위한 세계 최고의 제품

 

Eltec Pyroelectric Detectors are thermal detectors and respond almost linearly to a very wide spectrum of radiation. The sensing element is a thin pyroelectric lithium-tantalate crystal, that is suspended in air for maximum sensitivity and low frequency response.

Typical Applications

  • Thermal Infrared Detection
  • Solar Radiation Monitoring
  • Gas Analysis
  • Flame / Fire Detection
  • FTIR Spectrometry
  • Pyrometry / Temperature Sensing
  • Soft X-Ray - Visible - Infrared - Sub-Millimeter Detection
  • For Laser detectors refer to the Laser Page.

Make Your Choice

A detector is specified by the Model Number (such as 400)
and a Window (such as 1) making 400-1
For window information, refer to our Windows and Filter Page or to the Selector Guide.

Standard Product Special Product Available on Request
Eltec Model 400 contains only Sensing Element
standard size of Eltec detector 400 sensing crystal is 2mm round. Other dimensions are available
  • Basic pyroelectric Detector. Good low frequency response
  • Only sensing crystal. No amplifier included.
  • Ideal for experimental applications that do not require lowest possible S/N, such as low power Laser detection
  • Ideal for wide spectrum detection X-Ray - UV - Visible - IR - Far-IR
 Eltec pyroelectric detector model 400. Contains only lithium tantalate crystal. The package is TO39
Eltec Model 400-0. No window, for full spectrum.
Available from stock in our web-shop
Eltec Model 400-1
Germanium window, IR from 1.5 to 20 microns
Eltec Model 400-4
Sapphire window, UV 0.2 to IR 5 microns
Eltec Model 400-27
CaFl window, UV 0.12 to IR 10 microns 		Eltec Model 400-X
All other window options "X".
Refer to the optical filter page or our Filter Selector Guide for transmission data.
  • Larger or smaller element (crystal) size. (refer to Model 400M29-X for 2.5x2.5 mm size.)
  • Gigaohm load resistor included
Please inquire !
Custom made products may cause additional cost.
Model 404 Series Laboratory Grade Detectors with VM/CM Amplifier
  • Highest performance single element detectors.
  • Choice of voltage-mode and current-mode amplifier.
  • Electrical access to the sensing element (crystal).
  • Load/feedback resistors and frequency response can be altered with external resistors.
  • Electronics are shielded from incident light. Operation possible with transparent windows.
  • Ideal for laboratory use and product development, to define a suitable detector.
Due to the direct access pins to the sensing element and internal circuit, these detectors are not suitable for industrial production. 		Eltec pyroelectric detector series 404 are the higest performance devices available. The package is TO5
Model 404-X
Most universal VM/CM detector.
Model 404VM-X
only for VM operation.
Model 404CM-X
only for CM operation.

Specify window "X". 		Standard sensing element size of Eltec Model 404 is 2 mm round. Other sizes are available on request.
Model 406 Series Industrial Single Element Detectors with FET Amplifier
For very low frequency (0.1 to 5 Hz) temperature sensing and object detection.
Model 406-X
A very universal detector. Use only with windows that block visible light. 		Model 406M39-X
with higher gain FET amplifier. 		Eltec 406 series pyroelectric detectors have a standard sensing area of 2 mm round Eltec 406 pyroelectric single element detectors are in TO39 package
Model 481-X
in small TO18 package for compact sensor heads.

Specify window "X". 		Sensing element size of this Eltec miniature pyroelectric sensor is 1.5 mm square Eltec miniature pyroelectric sensor Model 481 is in the small TO18 package
Model 406 Series. Optimized for Flame Detection and Gas Analysis
in the 5 to 10 Hz Frequency range. Due to the lack of low frequency response, they deliver a more stable output signal. Built in FET amplifier.
Available with our gas filters, broadband windows or customer supplied filters.
Model 40612-X
2x2mm sensing element for focussed systems.
Model 40623-X
2.5x2.5mm sensing element for non focussed systems
 A sensing area of 2 mm square is ideal for gas analyzers with a focussed beam
A sensing area of 2.5mm square is the largest size available in the TO39 package to catch a maximum of energy over a wide angle for flame detectors. 		Model 406MBK-X
optimized for 20 Hz.
Model 406MBN-X
with brazed hermetic sapphire window. 		Eltec pyroelectric flame detectors are in TO39 package
Model 441 Series High Gain Single Element Detectors
These detectors include an amplifier with a gain of appx. 100. This eliminates the need for electronics close to the detector. They can be connected directy to a cable. Ideal for industrial sensors. Wide operating temperature range.
Model 441-X
Industrial temperature sensing.
Model 441M34-X
Fast version of 441. Choice of windows ("X") 		Eltec industrial pyroelectric sensors 441 have a sensing area of 2.5 mm square Eltec series 441 pyroelectric sensors are in TO39 package and ideal for industrial temperature sensing
Model 407 Series Thermally Compensated Single Element Detectors
These detectors have a compensating element behind the sensing element, that reduces the effect of ambient temperature changes by a factor of appx. 10.
This is very practical in many industrial applications, but they do not reach the performance (detectivity) of single element devices.
Model 407-X
A very universal detector. Use only with windows that block visible light.
With FET amplifier.
Model 405-X
with higher gain FET amplifier. 		Eltec 407 has two sensing crystals of 1x2.5mm each, one on top of the other, with only the front one exposed to radiation. The rear one is for temperature compensation. Model 407M56-43
CO2 gas sensor with hermetic brazed sapphire window. 		Eltec compensated pyroelectric detectors are in TO39 package
Model 407M24-X
3mm square sensing element.
Model 405M6-X
2.5mm square sensing element and higher gain FET amplifier. 		Eltec Model 407M24 has a large 3mm square sensing area. Viewing angle is somewhat reduced.
2.5 mm square combines large sensing area with wide vewing angle 		Eltec compensated pyroelectric sensors in TO39 package are available with different sensing crystal sizes.
Model 482-X
in small TO18 package for compact sensor heads.

Specify window "X". 		Sensing element size of this miniature Eltec pyroelectric detector is 1x1.9mm Model 482 is the smallest compensated Eltec pyroelectric detector. Package is TO18
Model 446 Series High Gain Thermally Compensated Single Element
These detectors include an amplifier with a gain of appx. 100 and have a compensating element. This eliminates the need for electronics close to the detector. They can be connected directy to a cable. Ideal for industrial sensors. Wide operating temperature range.
Model 446M2-3
Industrial hot object and hot glue detection.
Fast response.
Available from stock in our web-shop 		Model 446-X
Wide frequency range. Choice of windows ("X") Model 446M11-X
extended temperature range version 		Our rugged, fast and sensitive Model 446 pyroelectric sensors have a sensing area of 1x2.5 mm and are ideal for industrial hot object and hot glue detection. Model 446M10-X
with hermetic brazed sapphire window.
 Eltec 446 Series include a temperature compensating element and a high gain preamplifier in a TO5 package
Dual Element Detectors (Differential)
2 sensing elements side-by-side connected in parallel-opposed (differential) mode. These detectors need optics (focussing lens or mirror).Typical application is motion detection (alarm systems). There is no output from background radiation.
Model 5192-3
for professional alarm systems. Internal FET amplifier.
Model 429-3
same but 2 separate outputs. Two internal FET amplifiers. 		Model 447-3
with high gain internal amplifier. The choice for professional security systems. Wide temperature range.
Model 442-3
same but increased sensitivity (black elements) 		Eltec does not manufacture low cost dual detectors for consumer grade light switches and alarms. Dual detectors from Eltec are available in a variety of configurations in a TO39 package
Twin Channel, Optically Isolated Dual Wavelength Gas Detectors with FET amplifier
Model 459-X
Narrow spacing.
Model 479-X
Wide spacing.
Model 479M1-X
Higher gain version 		Twin channel detectors for gas analysis are generally designed to customer rquirements. Eltec can manufacture twin channel detectors with two individual narrow band filters in one TO39 package
All Eltec detectors are RoHS conform.

결제안내

배송안내

- 10만원 이상 구입시는 무료배송이며 그외에는 선불 결재로 발송합니다.
- 산간벽지나 도서지방은 별도의 추가금액을 지불하셔야 하는 경우가 있습니다.
고객님께서 주문하신 상품은 입금 확인후 배송해 드립니다. 다만, 상품종류에 따라서 상품의 배송이 다소 지연될 수 있습니다.

교환 및 반품안내

교환 및 반품이 가능한 경우
- 상품을 공급 받으신 날로부터 7일이내 단, 가전제품의
  경우 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우에는 교환/반품이 불가능합니다.
- 공급받으신 상품 및 용역의 내용이 표시.광고 내용과
  다르거나 다르게 이행된 경우에는 공급받은 날로부터 3월이내, 그사실을 알게 된 날로부터 30일이내

교환 및 반품이 불가능한 경우
- 고객님의 책임 있는 사유로 상품등이 멸실 또는 훼손된 경우. 단, 상품의 내용을 확인하기 위하여
  포장 등을 훼손한 경우는 제외
- 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우
  (예 : 가전제품, 식품, 음반 등, 단 액정화면이 부착된 노트북, LCD모니터, 디지털 카메라 등의 불량화소에
  따른 반품/교환은 제조사 기준에 따릅니다.)
- 고객님의 사용 또는 일부 소비에 의하여 상품의 가치가 현저히 감소한 경우 단, 화장품등의 경우 시용제품을
  제공한 경우에 한 합니다.
- 시간의 경과에 의하여 재판매가 곤란할 정도로 상품등의 가치가 현저히 감소한 경우
- 복제가 가능한 상품등의 포장을 훼손한 경우
  (자세한 내용은 고객만족센터 1:1 E-MAIL상담을 이용해 주시기 바랍니다.)

※ 고객님의 마음이 바뀌어 교환, 반품을 하실 경우 상품반송 비용은 고객님께서 부담하셔야 합니다.
  (색상 교환, 사이즈 교환 등 포함)

※ 상품구입후 단순변심은 환불되지 않습니다.


 A/S 안내

- 전자키트 및 센서 에 대하여 조립시 A/S 및 환불이 되지 않습니다.

- 전자키트 초기 불량일 경우 100% A/S 조치해 드립니다.

- 완제품 의 경우 외산의 제품이 대부분이여서 한달간 무상수리해드립니다.(국산품 제외)

- 완제품 국산제품의 경우 제조사의 A/S 조항을 따릅니다.

 

상품사용후기

상품후기쓰기 모두보기

게시물이 없습니다

상품 Q&A

상품문의하기 모두보기

게시물이 없습니다

판매자 정보

follow me

CUSTOMER CENTER

051-465-7774

AM 9:00 ~ PM 18:00

LUNCH PM 12:00 ~ PM 13:00

CLOSED토요일, 일요일, 법정공휴일



고객센터 연결

BANK ACCOUNT

예금주:박상근동창이지킷

기업은행

097-094280-01-012




주문조회 보기

company agreement privacy policy guide PC.VR
Company: EasyKit TEL : 051-465-7774
ADDRESS: 48822 부산광역시 동구 중앙대로180번길 12 (초량동) 진영B/D 401호
Business Registration NO: 194-35-00364
E-commerce Permit No : 2018-부산동구-0035
CEO: 박상근 Personal Information Manager : 박상근
email :swplanet@naver.com

호스팅 제공자: 심플렉스인터넷(주) DESIGNED BY. MOMOI